| Parameter |
Description |
Range |
| Move speed |
The current maximum pan and tilt speed. |
1-100 |
| Pan move time per degree |
Panning 1 degree takes this amount of time (unit = 1s/10000). Changing "Move speed" requires this parameter to be recalibrated. Calibration is done by requesting a 180 deg. pan (i.e. "rpan=180") at current "Move speed" and then adjusting this parameter until the request pans exactly 180 degrees. If pan speed(deg/sec) is known, this is calculated by 10000/(pan speed). |
1-15000 |
| Pan scale compensation |
Calibration constant to compensate for non linear pan speed values. A value of "0" will disable the compensation. Higher values will compensate with a higher pan speed and lower values will compensate with a lower pan speed. When changing the "Move speed" (see above), re-calibration is required. Calculate a pan request that will require only half the time of a tilt request (e.g. if the pan speed and the tilt speed in degrees/second is equal, "rpan=45&rtilt=90"). When sending this request, if the pan move is too small, increase this calibration constant, if the pan move is too big, reduce this calibration constant. |
-100 - 100 |
| Tilt move time per degree |
Tilting 1 degree takes this amount of time (unit = 1s/10000). Changing "Move speed" requires this parameter to be recalibrated. Calibration is done by requesting a 90 deg. tilt (i.e. "rtilt=90") at current "Move speed" and then adjusting this parameter until the request tilts exactly 90 degrees. If tilt speed(deg/sec) is known, this is calculated by 10000/(tilt speed). |
1-30000 |
| Tilt scale compensation |
Calibration constant to compensate for non linear tilt speed values. A value of "0" will disable the compensation. Higher values will compensate with a higher tilt speed and lower values will compensate with a lower tilt speed. When changing the "Move speed" (see above), re-calibration is required. Calculate a tilt request that will require only half the time of a pan request (e.g. if the pan speed and the tilt speed in degrees/second is equal, "rpan=180&rtilt=90"). When sending this request, if the tilt move is too small, increase this calibration constant, if the tilt move is too big, reduce this calibration constant. |
-100 - 100 |
| Zoom speed |
The current zoom speed. |
1-100 |
| Zoom per unit |
Calibration constant for zoom. Higher values give greater zoom changes. Calibrate at the most commonly used zoom speed, by confirming that a maximum zoom request performs a maximum zoom change. |
1-65535 |
| Focus speed |
The current focus speed. |
1-100 |
| Focus per unit |
Calibration constant for focus. Higher values give greater focus changes. Calibrate at the most commonly used focus speed, by confirming that a maximum focus request performs a maximum focus change. |
1-65535 |
| Iris speed |
The current iris speed. |
1-100 |
| Iris per unit |
Calibration constant for iris. Higher values give greater iris changes. Calibrate at the most commonly used iris speed, by confirming that a maximum iris request performs a maximum iris change. |
1-65535 |
| Pan bar range |
Range (in degrees) to use with "panbar" requests. Clicking at the very end of a bar will pan half this value in the corresponding direction. |
1-720 |
| Tilt bar range |
Range (in degrees) to use with "tiltbar" requests. Clicking at the very end of a bar will tilt half this value in the corresponding direction. |
1-720 |
| Current field angle |
The calibration constant for click-in-picture (center). Higher values give larger movements. Calibrate at minimum zoom (i.e. zoom wide) and at the most commonly used speed, by making sure that clicking on an object brings the object to the center of the image. |
1-1800 |
| Goto preset delay |
Time (in seconds) it takes for the image to stabilize it self, after the camera has performed the longest "goto preset action". Used for disabling/enabling image analysis (e.g. motion detection). |
0-100 |